发动机机油滤清器虑层强度分析及优化

针对机油滤清器工作工况下进出口压差、机油滤层强度及导流桩高度等问题, 通过试验测试与仿真相结合, 对滤清器初步设计进行了评估及优化, 以确保滤清器在工作工况下进出口压降及滤层强度能满足要求. 首先进行滤层性能试验, 得到滤层的惯性阻力系数和黏性阻力系数; 再通过滤层多孔介质CFD分析, 对滤清器进出口压降进行分析计算. 结果表明: 在-18℃、25℃和70℃的工况下, 进出口压降都小于10kPa, 满足相关要求. 针对滤层的最大主应力超过其抗拉强度的问题, 通过CAE仿真分析, 优化滤层与导流桩间隙, 将滤层最大主应力由110.1MPa降至36.99MPa, 小于其抗拉强度42.8MPa.     

Orientation dependent size effects in thermal buckling and post-buckling of nanoplates with cubic anisotropy

In this work, a continuum model is presented for size and orientation dependent thermal buckling and post-buckling of anisotropic nanoplates considering surface and bulk residual stresses. The model with von-Karman nonlinear strains and material cubic anisotropy of single crystals contains two parameters that reflect the orientation effects. Using Ritz method, closed form solutions are given for buckling temperature and post-buckling deflections. Regarding self-instability states of nanoplates and their recovering at higher temperatures, an experiment is discussed based on low pressurized membranes to verify the predictions. For simply supported nanoplates, the size effects are lowest when they are aligned in [100] direction. When the edges get clamped, the orientation dependence is ignorable and the behavior becomes symmetric about [510] axis. The surface residual stress makes drastic increase in buckling temperature of thinner nanoplates for which a minimum thickness is pointed to stay far from material softening at higher temperatures. Deflection of [100]-oriented buckled nanoplates is higher than [110] ones but this reverses at higher temperatures. The results for long nanoplates show that the buckling mode numbers are changed by orientation which is verified by FEM.     

航空导管弯曲试验的疲劳裂纹萌生寿命

飞行器液压导管受接头和卡箍等约束，在使用的振动环境中，会因弯曲应力而导致破裂，影响到飞行安全．本文对飞行器液压系统通用的不锈钢导管的裂纹萌生寿命进行了试验研究．首先在对8 mm、12 mm 无缺陷导管和含U 型缺口8 mm 导管的疲劳试验和有限元分析的基础上，得到了导管的最大拉应变-裂纹萌生寿命数据．然后采用基于强度极限和弹性模量估算法的Manson-Coffin 公式来预测导管裂纹萌生寿命．最后引入加载类型修正系数、表面质量修正系数、试样尺寸修正系数、应力集中敏感系数和有效应力集中系数，使修正后的公式对三种类型的导管均有较好的裂纹萌生寿命预测精度．     

Surfaces of Constant Mean Curvature Bounded by Two Planar Curves

In this paper we study constant mean curvature compact surfaces with two Jordan curves in parallel planes as boundary and we investigate the point at which the surface inherits the symmetries of its boundary.     

恒流应力下E2PROM隧道氧化层的退化特性研究

在电容测量的基础上研究了薄隧道氧化层在恒定Fowler-Nordheim(F-N)隧穿电流下的退化情况. 这种退化是恒流应力和时间的函数，对恒流应力大小的依赖性更加强烈，隧道氧化层在F-N电流下的退化是注入电荷密度(Q_inj)的函数. 在较低Q_inj下氧化层中发生正电荷俘获，在较高Q_inj下发生负电荷俘获，导致栅压变化的反复. 关键词： 2PROM')" href="#">E²PROM 隧道氧化层 退化 恒流应力     

光学低通滤波器的光学传递函数分析

光电成像系统的抽样过程会引起图像频谱在频谱空间上的多次复制,如果抽样过程不满足系统的奈奎斯特条件,相邻的频谱项就会产生混叠.光学传递函数可以反映系统中光学成像,抽样和重建等各个过程对图像信号频谱的响应.通过对使用光学低通滤波器(OLPF)光电成像系统的光学传递函数的分析,表明光学低通滤波器可以有效地限制图像的频谱宽度,使抽样满足奈奎斯特条件,达到消除频谱混叠,改善重建图像质量的目的.     

具有扩散的Lotka-Volterra系统的持续性

利用最大值原理结合上、下解的方法，讨论了一类具有扩散的竞争－捕食的Lotka-Volterra系统静态解的存在性与持续生存。     

Stress Distribution in an Infinite Elastic Body with a Locally Curved Fiber in a Geometrically Nonlinear Statement

Within the framework of a piecewise homogeneous body model, with the use of three-dimensional geometrically nonlinear exact equations of elasticity theory, a method for determining the stress—strain state in unidirectional fibrous composites with locally curved fibers is developed for the case where the interaction between the fibers is neglected. All the investigations are carried out for an infinite elastic body containing a single locally curved fiber. Numerical results illustrating the effect of geometrical nonlinearity on the distribution of the self-balanced normal and shear stresses acting on the interface and arising as a result of local curving of the fiber are presented.__________Russian translation published in Mekhanika Kompozitnykh Materialov, Vol. 41, No. 4, pp. 433–448, July–August, 2005.     

Numerical analysis of turbulent structure in compound meandering open channel by algebraic Reynolds stress model

The turbulent flow in a compound meandering channel with a rectangular cross section is one of the most complicated turbulent flows, because the flow behaviour is influenced by several kinds of forces, including centrifugal forces, pressure‐driven forces and shear stresses generated by momentum transfer between the main channel and the flood plain. Numerical analysis has been performed for the fully developed turbulent flow in a compound meandering open‐channel flow using an algebraic Reynolds stress model. The boundary‐fitted coordinate system is introduced as a method for coordinate transformation in order to set the boundary conditions along the complicated shape of the meandering open channel. The turbulence model consists of transport equations for turbulent energy and dissipation, in conjunction with an algebraic stress model based on the Reynolds stress transport equations. With reference to the pressure–strain term, we have made use of a modified pressure–strain term. The boundary condition of the fluctuating vertical velocity is set to zero not only for the free surface, but also for computational grid points next to the free surface, because experimental results have shown that the fluctuating vertical velocity approaches zero near the free surface. In order to examine the validity of the present numerical method and the turbulent model, the calculated results are compared with experimental data measured by laser Doppler anemometer. In addition, the compound meandering open channel is clarified somewhat based on the calculated results. As a result of the analysis, the present algebraic Reynolds stress model is shown to be able to reasonably predict the turbulent flow in a compound meandering open channel. Copyright © 2005 John Wiley & Sons, Ltd.